丙烯腈装置回收塔内聚合物生成原因的分析

针对丙烯腈生产过程中回收塔内聚合物堵塞降液管造成回收塔运行周期短的问题,通过对丙烯腈回收塔内各组分分布的模拟计算,直观显示了回收塔内各组分的浓度分布,发现了回收塔的聚合段与丙烯醛的富集段相吻合的现象,初步得出了回收塔内局部聚合的原因;通过对塔内聚合物的特性分析和评判,进一步证实了“回收塔内局部聚合严重是由于在聚合段丙烯醛聚集引起”这一现象;根据模拟计算结果和实际运行经验,提出了预防聚合物堵塞降液管的措施,并进行了部分生产验证,为丙烯腈生产企业延长装置运行周期提供了理论指导。     

对CFG桩质量缺陷的探讨

根据具体工程的概况及水文地质条件，分析了CFG桩在地下水位出现大面积缩颈现象和复合地基载荷试验达不到设计要求的原因，并介绍了地基补强措施，以满足工程质量的要求。     

卫星电视上行站信号自动监测系统

每个卫星电视上行站都必须对卫星转发器上的电视信号进行监测,才能及时发现卫星电视上行信号的异常变化,准确处理异常突发干扰。为实现自动、连续、实时监测,就需要建立卫星电视上行站射频信号自动监测系统。文章详细介绍了一个自动监测系统的设计及实现。     

弱碱三元复合驱与强碱三元复合驱的对比

三元复合驱即将成为大庆油田的主导开发技术,为了推荐出合适的三元复合驱类型,对比研究了弱碱三元复合驱与强碱三元复合驱。研究表明,弱碱三元复合驱可以比水驱提高采收率20%以上,与强碱三元复合驱相当;弱碱三元复合驱与强碱三元复合驱乳化液粘度都超过100 mPa.s,两种类型三元复合乳化能力相差不多,甚至弱碱三元复合驱乳化能力还略强一些;在注采能力、采油速度方面,弱碱三元复合驱甚至高于强碱三元复合驱;特别是在结垢程度上,弱碱三元复合驱比强碱三元复合驱弱,对生产井的影响较小。因此,在三元复合驱推广应用时应当选用弱碱三元复合驱。     

乳品企业原位清洗自动控制方案的实现

在调查国内乳品厂现状的基础上,借鉴从国外引进设备的乳品厂设计和使用经验,结合我国的实际情况,并融入若干年自控设计经验,综述了各工艺设备原位清洗自控方案、实现手段和方法。     

复合体系超低界面张力和碱在驱油过程中的实际作用

以物理模拟实验结果为依据并结合理论分析发现，在实际油藏的驱油过程中，础活性剂／聚合物（ASP）复合体系与原油的超低界面张力对于启动残余油滴和降低毛管阻力的作用均比以往所推断的要小；为使油／水界面张力达到超低而加入的大量强碱，将导致储层矿物的溶蚀、地层和井筒的严重结垢以及产出液的深度乳化，这对于复合驱的总体效果和效益都是不利的。因此，对于复合体系超低界面张力和碱在驱油过程中的实际作用研究应予以客观的评价，对于非超低界面张力体系驱油实际效果的研究应引起足够的重视.     

油气吸收回收系统的研究及工业应用——(Ⅰ)中型试验及结果分析

在蒸发油气吸收回收技术小试研究的基础上，开发出常温常压吸收法油气回收中试装置，并利用已开发的吸收剂AbsFOV-97进行了中试试验。结果表明，当系统进料气、吸收剂AbsFOV-97、汽油的体积流量比为10．0：1．0：0．5、真空泵解吸压力小于13．3kPa时，系统回收率高达97％以上，高于设计指标，且回收汽油的质量满足使用要求。统计数据表明，油气回收系统进料气、尾气中平均油气摩尔质量分别为65．51、48．97g／mol，该值可为油品蒸发损耗及其控制技术的评价提供参考。     

A Bluetooth Based Sensor Network for Civil Infrastructure Health Monitoring

Communicating with sensors has long been limited either to wired connections or to proprietary wireless communication protocols. Using a ubiquitous and inexpensive wireless communication technology to create Sensor Area Networks (SANs) will accelerate the extensive deployment of sensor technology. Bluetooth, an emerging, worldwide standard for inexpensive, local wireless communication is a viable choice for SANs because of its inherent support for some of the important requirements – low power, small form factor, low cost and sufficient communication range. In this paper we outline an approach, centered on the Bluetooth technology, to support a sensor network composed of fixed wireless sensors for health monitoring of highways, bridges and other civil infrastructures. We present a topology formation scheme that not only takes into account the traffic generated by different sensors but also the associated link strengths, buffer capacities and energy availability. The algorithm makes no particular assumptions as to the placement of nodes, and not all nodes need to be in radio proximity of each other. The output is a tree shaped scatternet rooted at the sensor hub (data logger) that is balanced in terms of traffic carried on each of the links. We also analyze the scheduling, routing and healing aspects of the resulting sensor-net topology.     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.